- Choosing a selection results in a full page refresh.
Couldn't load pickup availability
The TILT RACK E-W & N-S – GP is a robust rooftop solar mounting solution designed for efficient installation of high-capacity solar modules. This 6.0 kWp configuration supports 10 solar panels of 600 Wp each in a 5×2 layout.
Designed for both East-West (E-W) and North-South (N-S) mounting orientations, the system incorporates GP leg profiles and base supports, copper stabilizers, module clamps, long rails and stainless-steel fastening hardware.
The complete kit is supplied with the structural and installation components required for the specified 10-panel configuration, making it suitable for residential, commercial and industrial rooftop solar applications.
| Product | TILT RACK E-W & N-S – GP |
| System Capacity | 6.0 kWp / 6000 Wp |
| Panel Layout | 5 × 2 |
| Module Count | 10 Panels |
| Module Wattage | 600 Wp per module |
| Total Module Capacity | 6000 Wp / 6.0 kWp |
| Panel Orientation | East-West & North-South |
| System Type | GP |
| Leg Profiles | T1-L680 – GP & T1-L320 – GP |
| Base Support | TR Base Support 6H – GP |
| Stabilizer | CU 60×21×21×0.80, L1650 & L1450 |
| End Clamp | Z Clamp 35 |
| Mid Clamp | U Clamp |
| Long Rails | L2250, L2450 & L1425 |
| Rail Connector | L80 |
| Fasteners | SS304/A2 specified hardware |
Note: Final installation suitability should be verified based on module dimensions, roof conditions, structural requirements, applicable wind loads and project-specific engineering requirements.
| Component | Quantity |
|---|---|
| LEG PROFILE T1-L680 – GP | 12 |
| LEG PROFILE T1-L320 – GP | 12 |
| TR BASE SUPPORT 6H – GP | 24 |
| STABILIZER CU 60x21x21x0.80 L1650 | 16 |
| STABILIZER CU 60x21x21x0.80 L1450 | 24 |
| Z CLAMP 35 | 8 |
| U CLAMP | 16 |
| RAIL NUT (M8) | 24 |
| SPRING WASHER M8 SS304/A2 | 24 |
| PLAIN WASHER M8 SS304/A2 | 168 |
| ALLEN BOLT M8x70 | 72 |
| ALLEN BOLT M8x20 SS304/A2 | 24 |
| RIVET (ø4.8 x 19mm) | 96 |
| HEX NUT (M8) | 72 |
| RX-32 SCREW | 136 |
| EPDM TAPE (W-30mm x T-1mm x L-5m) | 0.552 |
| LONG RAIL L2250 | 4 |
| LONG RAIL L2450 | 4 |
| LONG RAIL L1425 | 4 |
| L-ANGLE 55 – D9 | 24 |
| CLAMP SPACER – PVC | 24 |
| RAIL CONNECTOR L80 | 8 |
| GRIP PLATE 3T x L90 | 8 |
This configuration is designed for 10 solar panels of 600 Wp each, providing a total capacity of 6.0 kWp (6000 Wp).
The system supports 10 solar modules arranged in a 5×2 layout.
The TILT RACK E-W & N-S – GP is designed for both East-West (E-W) and North-South (N-S) mounting orientations.
The kit includes 8 Z Clamps 35 and 16 U Clamps.
The kit includes CU stabilizers with a 60×21×21×0.80 profile in L1650 and L1450 lengths.
Yes. The kit includes L2250, L2450 and L1425 long rails, along with L80 rail connectors and grip plates.
Yes. The kit includes rail nuts, spring washers, plain washers, Allen bolts, rivets, hex nuts, RX-32 screws, EPDM tape, L-angles and PVC clamp spacers in the specified quantities.
This specific configuration is designed around 600 Wp modules, with 10 modules providing a total of 6000 Wp.
Yes. The TILT RACK E-W & N-S – GP is intended for rooftop solar mounting applications. Site conditions and structural requirements should be checked before installation.
The supplied kit is configured for the specified module arrangement. Compatibility with different module dimensions should be verified before ordering or installation.
Thanks for subscribing!
This email has been registered!