- Choosing a selection results in a full page refresh.
Couldn't load pickup availability
The TILT RACK E-W & N-S – ALU is an aluminium solar mounting system designed for rooftop and open-area solar installations requiring flexible East-West (E-W) and North-South (N-S) panel orientation. The system is designed to provide a stable and organized mounting platform for solar modules while allowing efficient use of available installation space.
This configuration supports 2 solar modules in a 2×1 arrangement, with a total system capacity of 1200 Wp when used with 600 Wp modules. The kit combines aluminium structural profiles, stainless-steel fasteners, module clamps, stabilizers and EPDM protection components for a complete mounting solution.
| Product | TILT RACK E-W & N-S – ALU |
| Panel Orientation | E-W & N-S |
| Panel Configuration | 2 × 1 |
| Module Count | 2 Modules |
| Module Wattage | 600 Wp per module |
| Total Capacity | 1200 Wp |
| Primary Material | Aluminium |
| Aluminium Grade | AL 6063-T6 (specified components) |
| Module Clamping | End Clamp + Mid Clamp |
| Fastener Material | SS304/A2 (specified fasteners) |
| Long Rail | L2450 – 2 Nos. |
Note: Actual installation suitability should be verified against module dimensions, roof conditions, wind loads and project-specific structural requirements before installation.
| Component | Quantity |
|---|---|
| LEG PROFILE T1-L680 | 3 |
| LEG PROFILE T3-L320 | 3 |
| TR BASE SUPPORT 6H | 6 |
| CLAMPING PLATE 15D | 6 |
| STABILIZER LW19T1.8 L1650 AL 6063-T6 | 5 |
| STABILIZER LW19T1.8 L1450 AL 6063-T6 | 6 |
| END CLAMP (Z Type) – 35mm | 4 |
| MID CLAMP (U Type) – 35mm AL 6063-T6 | 2 |
| RAIL NUT – M8 | 12 |
| SPRING WASHER M8 SS304/A2 | 6 |
| PLAIN WASHER – M8 SS304/A2 | 54 |
| ALLEN BOLT M8x70 | 18 |
| ALLEN BOLT M8x20 SS304/A2 | 16 |
| ALLEN BOLT M8x25 SS304/A2 | 2 |
| POP RIVET 4.8x19 – AL | 24 |
| HEX. NUT M8 SS304/A2 | 18 |
| EPDM TAPE 3mm x 30mm x 5m | 0.138 |
| SELF DRILLING SCREW 12x32 RX (Epoxy Coated) | 44 |
| L-ANGLE 55 – D9 | 6 |
| CLAMP SPACER – PVC | 6 |
| LONG RAIL L2450 | 2 |
Kit configuration: Complete mounting hardware for one 2-module / 2×1 installation.
It is an aluminium solar mounting system designed to support solar modules in East-West and North-South orientation configurations.
The supplied configuration is designed for 2 solar modules in a 2×1 arrangement.
With two 600 Wp modules, the total module capacity is 1200 Wp.
Yes. The kit includes 4 Nos. of 35mm Z-Type End Clamps and 2 Nos. of 35mm U-Type Mid Clamps.
The system primarily uses aluminium components, with specified stabilizer and clamp components made from AL 6063-T6.
Yes. The kit includes Allen bolts, rail nuts, washers, nuts, pop rivets and other specified mounting hardware.
Yes. The kit includes EPDM Tape 3mm x 30mm x 5m.
Suitability depends on the roof type, module dimensions, installation conditions, wind loads and project-specific structural requirements. Always verify the system design before installation.
Thanks for subscribing!
This email has been registered!