- Choosing a selection results in a full page refresh.
Couldn't load pickup availability
The TILT RACK E-W & N-S – ALU is an aluminium solar mounting solution designed for rooftop solar installations requiring a stable and efficient mounting arrangement. This 6 kWp configuration is designed to accommodate 10 solar panels of 600 Wp each in a 5×2 layout.
Designed to support both East-West (E-W) and North-South (N-S) panel orientations, the system combines aluminium structural components, stabilizers, rails, clamps and stainless-steel hardware to provide a complete mounting solution for the specified configuration.
The complete kit includes leg profiles, base supports, stabilizers, long rails, rail connectors, end and mid clamps, grip plates, EPDM tape and the required fastening hardware.
| Product | TILT RACK E-W & N-S – ALU |
| System Capacity | 6 kWp / 6000 Wp |
| Panel Layout | 5 × 2 |
| Module Count | 10 Panels |
| Module Wattage | 600 Wp per module |
| Total Module Capacity | 6000 Wp / 6 kWp |
| Panel Orientation | E-W & N-S |
| Primary Material | Aluminium |
| Aluminium Grade | AL 6063-T6 for specified components |
| End Clamp | Z Type – 35 mm |
| Mid Clamp | U Type – 35 mm AL 6063-T6 |
| Long Rails | L2250, L2450 & L1425 |
| Rail Connector | L80 |
| Fastener Material | SS304/A2 for specified fasteners |
Note: Final installation suitability should be verified according to module dimensions, roof conditions, structural requirements, wind loads and project-specific design.
| Component | Quantity |
|---|---|
| LEG PROFILE T1-L680 | 12 |
| LEG PROFILE T3-L320 | 12 |
| TR BASE SUPPORT 6H | 24 |
| CLAMPING PLATE 15D | 24 |
| STABILIZER LW19T1.8 L1650 AL 6063-T6 | 16 |
| STABILIZER LW19T1.8 L1450 AL 6063-T6 | 24 |
| END CLAMP (Z Type) – 35mm | 8 |
| MID CLAMP (U Type) – 35mm AL 6063-T6 | 16 |
| RAIL NUT – M8 | 48 |
| SPRING WASHER M8 SS304/A2 | 24 |
| PLAIN WASHER M8 SS304/A2 | 232 |
| ALLEN BOLT M8x70 | 72 |
| ALLEN BOLT M8x20 SS304/A2 | 72 |
| ALLEN BOLT M8x25 | 16 |
| POP RIVET 4.8x19 – AL | 96 |
| HEX NUT M8 SS304/A2 | 72 |
| EPDM TAPE 3mmx30mmx5m | 0.552 |
| SELF DRILLING SCREW 12x32 RX (Epoxy Coated) | 112 |
| L-ANGLE 55 – D9 | 24 |
| CLAMP SPACER – PVC | 24 |
| LONG RAIL L2250 | 4 |
| LONG RAIL L2450 | 4 |
| LONG RAIL L1425 | 4 |
| RAIL CONNECTOR L80 | 8 |
| GRIP PLATE 3TxL90 | 8 |
This configuration is designed for 10 solar panels of 600 Wp each, providing a total capacity of 6 kWp (6000 Wp).
The 6 kW configuration supports 10 solar modules arranged in a 5×2 layout.
The system is designed for both East-West (E-W) and North-South (N-S) mounting orientations.
The kit includes Z Type 35 mm End Clamps and U Type 35 mm AL 6063-T6 Mid Clamps.
The system primarily uses aluminium components, with specified structural and stabilizer components made from AL 6063-T6. Specified fasteners are supplied in SS304/A2.
Yes. The kit includes L2250, L2450 and L1425 Long Rails, along with L80 Rail Connectors.
Yes. The kit includes Allen bolts, rail nuts, washers, nuts, pop rivets, self-drilling screws, EPDM tape, grip plates and other specified components.
Yes. The kit includes EPDM Tape 3mm × 30mm × 5m.
Yes. The TILT RACK E-W & N-S – ALU is designed as a mounting solution for the specified rooftop solar configuration.
This specific configuration is calculated for 10 × 600 Wp modules. For different module dimensions or capacities, compatibility should be verified before ordering.
Thanks for subscribing!
This email has been registered!