- Choosing a selection results in a full page refresh.
Couldn't load pickup availability
The TILT RACK E-W & N-S – ALU 2.4 kW is an aluminium solar mounting solution designed for rooftop solar installations requiring a stable and organized mounting arrangement for multiple solar modules. This configuration supports 4 solar panels in a 4×1 layout.
Designed around a 2400 Wp total module capacity, the system is suitable for installations using four 600 Wp solar modules. The kit includes aluminium structural profiles, stabilizers, rails, module clamps, stainless-steel hardware, EPDM tape and other required mounting components.
The system supports East-West and North-South orientation and is supplied as a complete mounting kit for the specified 4-panel configuration.
| Product | TILT RACK E-W & N-S – ALU |
| System Capacity | 2.4 kW / 2400 Wp |
| Panel Layout | 4 × 1 |
| Module Count | 4 Modules |
| Module Wattage | 600 Wp per module |
| Total WP | 2400 Wp |
| Panel Orientation | E-W & N-S |
| Primary Material | Aluminium |
| Aluminium Grade | AL 6063-T6 for specified components |
| Module Clamping | Z-Type End Clamp + U-Type Mid Clamp |
| End Clamp | 35mm – 4 Nos. |
| Mid Clamp | 35mm AL 6063-T6 – 6 Nos. |
| Long Rail | L2250 – 2 Nos. + L2850 – 2 Nos. |
| Rail Connector | L80 – 2 Nos. |
| Fastener Material | SS304/A2 for specified fasteners |
Note: Final installation suitability should be checked according to the solar module dimensions, roof conditions, wind load, structural requirements and project-specific design.
| Component | Quantity |
|---|---|
| LEG PROFILE T1-L680 | 5 |
| LEG PROFILE T3-L320 | 5 |
| TR BASE SUPPORT 6H | 10 |
| CLAMPING PLATE 15D | 10 |
| STABILIZER LW19T1.8 L1650 AL 6063-T6 | 7 |
| STABILIZER LW19T1.8 L1450 AL 6063-T6 | 10 |
| END CLAMP (Z Type) – 35mm | 4 |
| MID CLAMP (U Type) – 35mm AL 6063-T6 | 6 |
| RAIL NUT – M8 | 20 |
| SPRING WASHER M8 SS304/A2 | 10 |
| PLAIN WASHER – M8 SS304/A2 | 94 |
| ALLEN BOLT M8x70 | 30 |
| ALLEN BOLT M8x20 SS304/A2 | 28 |
| ALLEN BOLT M8x25 | 6 |
| POP RIVET 4.8x19 – AL | 40 |
| HEX. NUT M8 SS304/A2 | 30 |
| EPDM TAPE 3mm x 30mm x 5m | 0.23 |
| SELF DRILLING SCREW 12x32 RX (Epoxy Coated) | 52 |
| L-ANGLE 55 – D9 | 10 |
| CLAMP SPACER – PVC | 10 |
| LONG RAIL L2250 | 2 |
| LONG RAIL L2850 | 2 |
| RAIL CONNECTOR L80 | 2 |
| GRIP PLATE 3T x L90 | 2 |
Kit configuration: Complete mounting kit for a 4-panel / 4×1 configuration with a total module capacity of 2400 Wp.
This configuration is designed for 4 solar modules of 600 Wp each, giving a total module capacity of 2400 Wp (2.4 kW).
The kit is configured for 4 solar panels in a 4×1 layout.
The product is designed for East-West (E-W) and North-South (N-S) panel orientation requirements.
Yes. The kit includes 4 Nos. of 35mm Z-Type End Clamps and 6 Nos. of 35mm U-Type Mid Clamps.
The mounting system uses aluminium components, including specified components manufactured from AL 6063-T6.
Yes. The kit includes 2 Nos. L2250 Long Rails, 2 Nos. L2850 Long Rails and 2 Nos. L80 Rail Connectors.
Yes. The kit includes Allen bolts, rail nuts, washers, nuts, pop rivets, self-drilling screws and other specified mounting hardware.
Yes. The kit includes EPDM Tape 3mm x 30mm x 5m.
Suitability depends on the roof type, module dimensions, structural conditions, wind loads and project-specific requirements. The system should be checked against the actual site conditions before installation.
Thanks for subscribing!
This email has been registered!